| Patch for |
Océ TDS300 1.0.2, 1.1.1, 1.1.2, 1.1.4
Océ TDS320 1.0.0, 1.0.1
Océ TDS400 2.0.2, 2.1.1, 2.1.2, 2.1.4
Océ TDS450 1.0.0 (TDS400 3.0.0)/1.0.1 (TDS400 3.0.1)
Océ TDS600 4.0.2, 4.1.1, 4.1.2, 4.1.4
Océ TDS800 2.0.2, 2.1.1, 2.1.2, 2.1.4
Océ TDS860 1.0, 1.0.2 Océ TCS400 2.1, 2.2, 2.2.3 |
| Microsoft bulletin |
MS05-027 |
| File details |
Name: patch_shf005a.exe
Size: 514 Kb
Revision date: 4/12/2006
Download now » (registration required)
|
Patch installation prerequisites
Before applying the patch for MS05-027 for following Océ systems :
Océ TDS300 1.0.2, 1.1.1, 1.1.2
Océ TDS400 2.0.2, 2.1.1, 2.1.2
Océ TDS600 4.0.2, 4.1.1, 4.1.2
Océ TDS800 2.0.2, 2.1.1, 2.1.2
Océ TDS860 1.0 Océ TCS400 2.1, 2.2
you should first check that previous patches for
MS05-011, MS05-019 have been applied,
a. Make a « Print settings » (Refer to your Printer User manual
for more details)
b. Go to the last printout page in the section:
SDS - CONTROL PARAMETERS 22-1, the last line is called:
Patches installed = ………………………… <value>
c. Consult Océ patch(es) identification here with <value> and your Océ Product version and check patches "patch_shf003" (corresponding to Microsoft MS05-011)
and "patch_shf004" (corresponding to Microsoft MS05-019)
are listed.
d. If previous mentionned patches are applied, please follow
instructions below, otherwise install first MS05-011 and
Patch installation instructions
1. Download the patch file and save the file on your computer
(Win98/WinMe/Win2000/WinXP/Winserver2003)
2. Create a floppy containing the patch :
- Doubleclick on the saved file (It is an executable which will
guide you through the creation process of the patch diskette)
- Follow the instructions on the screen
3. Shutdown the Océ Power Logic Controller
4. Insert the previously created patch diskette in the
Océ Power Logic controller floppy drive.
5. Power ON the Océ Power Logic Controller.
6. Wait until the patch is applied : a melody is played
(you will hear 2 times a 3 tonal beeps)
- it should take about ~3 minutes on a GX270 PC
- before the melody is played, a PC reboot will occur
- For Systems equipped with a monitor, an error message
may pop up on the controller screen : Ignore it and let the
process go on.
7. Remove the patch diskette from the floppy drive
Verifying if the patch was applied successfully
1. Make a « Print settings » (Refer to your Printer User manual for
more details)
2. Go to the last printout page in the section:
SDS - CONTROL PARAMETERS 22-1, the last line is called:
Patches installed = ………………………… <value>
3. Consult Océ patch(es) identification here with <value>
Troubleshooting
• 2 rapid beeps are played when Patch has already been applied
• 2 long beeps are played when Patch file is corrupted
• Nothing happens or 7 rapid beeps are played when Patch cannot be
applied (Wrong Océ TDSX00/TCS400 version)
|
